產品介紹：
Product introduction:
1..橡膠止水帶是采用天然橡膠與各種合成橡膠為主要原料，摻加各種助劑及填充料，經塑煉，混煉， 壓制成型，其品種規格較多，有橋型、山型、P型、R型、U型、Z型、乙型、T型、H型、E型、Q型等。該止水材料具有良好的彈性，耐磨性、耐老化性和抗撕裂性能，適應變形能力強、防水性能好，溫度使用范圍-45℃-+60℃。當溫度超過+70℃，以及強烈的氧化作用或受油類等有機溶劑侵蝕時，均不得使用該產品。
1.. Rubber sealing strip is made of natural rubber and various synthetic rubber as the main raw material, and the filling material mixed with various additives, through mixing, mixing, molding, the more varieties of different specifications, bridge, mountain type, P type, R type, U type, Z type, T type, H type, type B E type and Q type, etc.. The sealing material has good elasticity, wear resistance, aging resistance and tear resistance. It has strong deformation capacity and waterproof performance, and its temperature range is -45 -+60 C. The product should not be used when the temperature is more than +70 C, as well as the strong oxidation or the corrosion of organic solvents, such as oil.
2.主要設置在分部施工縫處,以增加兩次混凝土施工結合面積,主要來滿足施工縫防水要求,應按其厚度分別采用折疊咬接或搭接；
The 2. is mainly located in the construction joints of the sub section, so as to increase the two times of the concrete construction joint area, mainly to meet the waterproof requirements of the construction joints.
3.止水帶鋼板型號是寬300mm,厚3mm的鋼板,長度3m1塊,材質為Q235鋼。施工時用對拉螺栓做水平支撐架,確保止水帶的垂直度及高程滿足設計及規范要求;混凝土澆筑完畢后要及時清理止水鋼板上部被混凝土污染部分,防止上部混凝土澆筑時與鋼板結合不良;下部施工完畢后,盡早鑿毛清理,確保上部施工時混凝土能良好的結合;澆筑上部混凝土前,應用高壓或水槍沖洗底部混凝土,清除上部結構施工時散落的灰渣等污染物,在澆筑上部結構混凝土?xí)r,首層應該先澆筑2cm左右厚度的同等標號砂漿,一方面潤濕先期施工的混凝土表層,起到良好的結合層的作用,另一方面來檢查模板支護情況,確保構筑物外觀尺寸符合設計及規范要求。設置鋼板止水帶在一定程度上解決了因?yàn)槭┕すに囁较拗?留置施工縫而發生滲漏的問題。
3. water stop strip plate model is wide 300mm, thick 3mm steel plate, length 3M1 block, material is Q235 steel. With the bolt horizontal supporting frame construction, ensure the verticality and elevation of strip to meet the design requirements and specifications; after the concrete pouring to clean up the upper sealing plate is part of the pollution of concrete, concrete pouring and prevent the upper plate and lower side; after the construction as soon as possible, cut hair clean, ensure the concrete construction can be a good combination; the upper concrete pouring, using high pressure water gun flushing or bottom concrete, scattered clear upper structure construction when the ash and other pollutants in the upper part of the structure of concrete pouring, the first layer should be equally labeled first mortar pouring 2cm about the thickness of the concrete surface, a pre wetting construction, play a good combination of layers the role, on the other hand to check the template support, ensure the structure appearance size meet the design requirements and norms. To a certain extent, the installation of steel plate has solved the problem that the construction seams must be leaked because of the limit of the construction technology.
4.這種方法也有三方面的不足之處:①由于使用大量的鋼板及支撐構件造,不經濟;②施工工藝較復雜,需分段焊接止水鋼板、支撐結構,在構筑物鋼筋結構復雜時安裝鋼板較困難,下部結構施工完畢后,要清理被污染的鋼板;③防滲效果不理想,下部結構澆筑混凝土?xí)r經常碰撞鋼板,導致其變形移位,混凝土澆筑高程也難以控制,上部結構澆筑混凝土?xí)r振搗困難,經常因?yàn)槁┱癜粗圃觳馁|(zhì)分為： 橡膠止水帶（R），如：天然膠、氯丁膠、丁苯膠等
This method has 4. shortcomings in three aspects: 1. Due to extensive use of steel plate and a supporting component of high cost, not the economy; the construction process is relatively complex, need welding sealing plate, supporting structure, the installation plate is difficult in building steel structure is complex, the lower part of the structure after completion of construction, to clean the polluted the steel plate; the anti-seepage effect is not ideal, the lower part of the structure of pouring concrete often leads to the deformation of plate collision, displacement, concrete pouring height is also difficult to control, the upper structure of pouring concrete vibration is difficult, often because of the leakage of vibration in manufacturing rubber waterstop material is divided into: (R), such as: natural rubber, chloroprene rubber styrene butadiene rubber, etc.
塑料止水帶（P），如：聚氯乙烯、聚乙烯等
Plastic water stop (P), such as PVC, PE, etc.
金屬止水帶（M），如：銅、不銹鋼、碳鋼等
Metal water stop (M), such as copper, stainless steel, carbon steel, etc.

查看全部介紹